FRONT DOOR BLACK OUT TAPE > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL


    B281274

  1. Using a moulding remover, detach the 2 clips and 4 claws.

  1. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.



4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    B281275

  1. Detach the 2 clips and remove the front door lower frame bracket garnish.



5. REMOVE DOOR PULL HANDLE


    B277022

  1. Remove the screw and door pull handle.



6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    B277024E01

  1. Remove the clip and screw.

  1. Detach the 8 clips and remove the front door trim board.

    Text in Illustration 
    *1
    		Clip
    *2
    		Screw


7. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH


B113822

  1. w/ Power Mirror Control System:
    Disconnect the mirror connector.

  1. Remove the 3 nuts.

  1. Push down the claw and remove the outer rear view mirror assembly LH.



8. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    B277027E01

  1. Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.



    B277028

  1. Disconnect the front door inside locking cable and front door lock remote control cable and remove the front door inside handle.



9. REMOVE FRONT DOOR NO. 1 TRIM BRACKET


    B277026

  1. Remove the 2 screws and front door No. 1 trim bracket.



10. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    B281060

  1. Pull out the front door inside locking cable, front door lock remote control cable and wire harness from the front door service hole cover, and then remove the front door service hole cover.

    HINT:
    Remove any remaining butyl tape from the front door panel.


11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

  1. Temporarily install the power window regulator master switch assembly with front door armrest base panel.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front door glass sub-assembly so that the front door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Remove the power window regulator master switch assembly with front door armrest base panel.



    B277030

  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the front door glass to fall.


    B277031E01

  1. Remove the front door glass as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the front door glass.


12. REMOVE FRONT DOOR OUTER GLASS WEATHERSTRIP ASSEMBLY LH


    B279194E01

  1. Put protective tape around the front door outer glass weatherstrip.

    Text in Illustration 
    *1
    		Protective Tape

  1. Detach the 5 claws and remove the front door outer glass weatherstrip.



13. REMOVE FRONT DOOR GLASS RUN LH


    B277034

  1. Remove the front door glass run.



14. REMOVE NO. 1 BLACK OUT TAPE LH

HINT:
When removing the No. 1 black out tape, heat the vehicle body and No. 1 black out tape using a heat light.

Standard:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
No. 1 Black Out Tape
40 to 60°C (104 to 140°F)

NOTICE:
Do not heat the vehicle body or No. 1 black out tape excessively.


    B279255

  1. Pull back an edge of the No. 1 black out tape and pull it parallel to the vehicle body to remove it.