REAR DOOR BLACK OUT TAPE > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B277098
  1. Using a moulding remover, detach the 2 clips and 2 claws.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



4. REMOVE DOOR PULL HANDLE


    B277099
  1. Remove the screw and door pull handle.



5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B279384
  1. Remove the screw.

  1. Detach the 10 clips and remove the rear door trim board.



6. REMOVE REAR DOOR OUTER GLASS WEATHERSTRIP LH


    B279385E01
  1. Put protective tape around the rear door outer glass weatherstrip.

    Text in Illustration 
    *1
    Protective Tape
  1. Detach the 4 claws and remove the rear door outer glass weatherstrip.



7. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    B279395E01
  1. Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.



    B277028
  1. Disconnect the rear door inside locking cable and rear door lock remote control cable and remove the rear door inside handle.



8. REMOVE REAR DOOR NO. 2 TRIM BRACKET


    B277102
  1. Remove the 2 screws and rear door No. 2 trim bracket.



9. REMOVE REAR DOOR SERVICE HOLE COVER LH


    B279386
  1. Pull out the rear door inside locking cable, rear door lock remote control cable and wire harness from the rear door service hole cover, and then remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the rear door panel.


10. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
  1. Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the rear door glass so that the rear door glass channel can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
  1. Remove the rear power window regulator switch assembly with rear door armrest base panel.



    B279387
  1. Partially remove the rear door glass run as shown in the illustration.



    B279388E01
  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window division bar may fall and become damaged.
    Text in Illustration 
    *1
    Temporary Bolt
  1. Remove the screw and bolt.



    B279389
  1. Remove the rear door window division bar together with the rear door glass run as shown in the illustration.

  1. Remove the rear door window division bar from the rear door glass run.



11. REMOVE REAR DOOR GLASS RUN LH


    B279390
  1. Remove the front side of the rear door glass run.



12. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    B279393
  1. Remove the rear door quarter window glass.



13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    B279394
  1. Remove the rear door glass from the rear door window regulator assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


14. REMOVE NO. 2 BLACK OUT TAPE LH

HINT:
When removing the No. 2 black out tape, heat the vehicle body and No. 2 black out tape using a heat light.

Standard:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
No. 2 Black Out Tape
40 to 60°C (104 to 140°F)

NOTICE:
Do not heat the vehicle body or No. 2 black out tape excessively.


    B279391
  1. Pull back an edge of the No. 2 black out tape and pull it parallel to the vehicle body to remove it.