FRONT DOOR LOCK > REMOVAL

for Preparation Click here



1. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    B173076
  1. Using a clip remover, remove the snap ring.

  1. Remove the front door window regulator handle assembly and front door regulator inside handle plate.



2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL


    B190634
  1. Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel.



3. REMOVE FRONT ARMREST UPPER BASE PANEL (w/o Power Window)


    B190635
  1. Using a moulding remover, disengage the 2 clips and 6 claws, and remove the front armrest upper base panel.

  1. w/ Power Door Lock:

    1. Disconnect the connector.



4. REMOVE FRONT ARMREST UPPER BASE PANEL (w/ Power Window)


    B190636
  1. Using a moulding remover, disengage the 2 clips and 6 claws.

  1. Disconnect the connector and remove the front armrest upper base panel.



5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B163639E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw and disconnect the door armrest cap.



    B159116
  1. Remove the 2 screws.



    B190689
  1. Using a clip remover, disengage the 10 clips.

  1. Disengage the 5 claws and separate the front door trim board sub-assembly from the front door inner glass weatherstrip.



    B159118
  1. Disengage the 2 claws and disconnect the front door inside handle sub-assembly.



6. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B159119
  1. Disconnect the front door lock remote control cable and front door inside locking cable, and remove the front door inside handle sub-assembly.



7. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    B159123
  1. Remove the front door inner glass weatherstrip from the front door panel.



8. REMOVE FRONT DOOR TRIM BRACKET


    B184689
  1. Remove the 2 screws and the front door trim bracket.



9. REMOVE FRONT DOOR SERVICE HOLE COVER


  1. w/ Power door lock:



      B177203
    1. Disconnect the connector.



    B177204
  1. Remove the front door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.


10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.



    B159126
  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.


    B184676E01
  1. Remove the front door glass sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


11. REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION


    B184691
  1. Remove the 2 bolts.

  1. Disengage the 2 guides and remove the front door No. 2 stiffener cushion.



12. REMOVE FRONT DOOR GLASS RUN


    B177208
  1. Remove the front door glass run.



13. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B159133E01
  1. Remove the bolt and the front door rear lower frame sub-assembly as shown in the illustration.



14. REMOVE FRONT DOOR OUTSIDE HANDLE COVER


    B159134
  1. Remove the hole plug.

  1. Using a "TORX" socket wrench (T30), loosen the screw and remove the front door outside handle cover and the door lock key cylinder as a unit.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.


    B159135
  1. Using a screwdriver, disengage the 2 claws and remove the front door outside handle cover.



15. REMOVE FRONT DOOR LOCK ASSEMBLY (w/o Power Door Lock)


    B177209
  1. Using a "TORX" socket wrench (T30), remove the 3 screws.

  1. Slide the front door lock assembly downward, and remove the front door lock assembly and cables as a unit.



16. REMOVE FRONT DOOR LOCK ASSEMBLY (w/ Power Door Lock)


    B159145
  1. Using a "TORX" socket wrench (T30), remove the 3 screws.

  1. Slide the front door lock assembly downward, and remove the front door lock assembly and cables as a unit.

  1. Remove the door lock wiring harness seal from the front door lock assembly.



17. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Power Door Lock)


    B177211
  1. Remove the front door lock remote control cable assembly.



18. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Power Door Lock)


    B159147
  1. Remove the front door lock remote control cable assembly.



19. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Power Door Lock)


    B177212
  1. Remove the front door inside locking cable assembly.



20. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Power Door Lock)


    B159148
  1. Using a screwdriver, disengage the 3 claws.

    HINT:
    Tape the screwdriver tip before use.


    B159149
  1. Remove the front door inside locking cable assembly.